Submersible Pump Guide: Types, Sump Pits, Float Switch and Safety
"Baha sa garahe? Puno ng tubig ang hukay? O malalim na balon?" A submersible pump sits right in the water and pushes it up and away. This guide explains how it works, why it must stay fully underwater, the three main types, how to choose one, how to set the float switch, how to build a sump pit, and the safety rules you should never skip.
SHOP SUBMERSIBLE PUMPS HOW TO BUILD A SUMP PIT ↓Watch: Jam Explains the Submersible Pump
How Does a Submersible Pump Work?
A submersible pump is a sealed electric pump that sits under the water it is pumping. Instead of sucking water up from above like a surface pump, it pushes the water up through a hose or pipe. That is why it needs no priming, runs quietly, and is cooled by the water around it.
Why It Must Stay Fully Underwater
- The water cools the motor. Out of the water, the motor heats up quickly.
- The intake (strainer) at the bottom must stay covered. Once it starts sucking air, the pump loses flow.
The 3 Main Types
Tanks, transfer and irrigation
For clear water with little debris. Examples: Ingco SPD7501-5 · Ingco SPC3708-5.
Floods, mud and septic
Bigger passages (and cutter types) for muddy water and solids. Examples: Shimge WVSD with float switch · Ingco SPD7508-5 · Shinsetsu SEP-132CF.
Water supply for home or farm
A slim pump lowered into a 4-inch well casing, usually with a control box. Examples: Ingco DWP7501-5 + control box · Wilo PSS.
Where Submersible Pumps Are Used
Flood removal
Garages, basements and flooded yards.
Construction dewatering
Excavations, footings and pits full of water.
Fishponds & irrigation
Moving water for farms and ponds.
Tank transfer
Filling or emptying water tanks.
Well water supply
Deep well pumps for homes and farms. There's even a solar deep well pump for off-grid farms.
How to Choose: Head vs Flow
| Spec | What it means | Example |
|---|---|---|
| Head | How high the pump can push the water (meters) | Ingco SPD7501-5: max head 8m |
| Flow | How much water it moves per hour | Ingco SPD7501-5: up to 13,000 L/h |
Use a Float Switch, and Set It Right
A float switch turns the pump on automatically when the water rises and off when it drops, so the pump never runs dry.
Shallow Water? Build a Sump Pit
If the water on the floor is too shallow to cover the pump, dig a sump pit: a hole at the lowest point of the basement, garage or construction site where the water flows in and collects. Because the pit is deep, the pump always stays submerged and doesn't keep switching on and off.
- Firm base: set the pump on a solid block, not on mud, so it doesn't suck up silt.
- Float switch inside the pit for automatic on and off.
- Check valve on the discharge pipe so the water doesn't flow back into the pit.
- Proper drainage: send the water to a drain or safe area, away from the house.
- Cover the pit so nobody falls in.
Portable vs Permanent Installation
Drop it in and attach a hose
Lower the pump into the hole on a rope, connect a lay-flat hose and pump. Ideal for floods and construction.
Guide rails and a lifting chain
The pump sits on guide rails in a concrete pit and couples to a fixed discharge pipe. Lift it out with the chain for cleaning.
Safety Muna
- Never run it without water.
- Never lift it by the power cable. Use a rope or chain on the handle.
- Unplug it before touching the pump or stepping into the water.
- Ground it and use a safety breaker (RCD / GFCI). Water and electricity don't mix.
- Clean the strainer regularly.
Frequently Asked Questions
Does a submersible pump need priming?
Clean water or dirty water pump for floods?
How deep should the water be?
Why do I need a check valve?
Which size should I buy?
Find the Right Submersible Pump
May tanong ka pa? I-message mo lang kami, tutulungan ka naming pumili ng tamang pump para sa baha, construction o balon.
SHOP SUBMERSIBLE PUMPS DEEP WELL PUMPS