In Tool Expert Explains 0 comment

Circular Saw Guide: Uses, Blades (24T vs 60T) & Safety for Filipinos (2026)

Miss Tin of KHM Megatools explains circular saws and saw blades
KHM MEGATOOLS · BEGINNER'S GUIDE 2026

Circular Saw Guide: Uses, Blades (24T vs 60T) & Safety for Filipino Carpenters and DIYers

"Bakit magaspang ang putol ko sa plywood? Sira na ba ang saw ko?" Most of the time, the saw is fine. The blade is the problem. This guide explains what a circular saw does, why the 7-1/4 inch saw is the everyday size in the Philippines, which blade to use for lumber, plywood, aluminum and fiber cement board, and the safety habits that prevent kickback.

SHOP CIRCULAR SAWS WHICH BLADE DO I NEED? ↓
Quick Navigation Watch Video What It Is Why Teeth Matter Why 7-1/4 Inch The 4 Blades Safety Checklist Blade by Material FAQs

Watch: Miss Tin Explains Circular Saws

Prefer watching? Our Tool Expert Miss Tin explains everything in this guide in about 90 seconds.

WATCH ON YOUTUBE WATCH ON FACEBOOK

What Is a Circular Saw?

A circular saw is a handheld power saw that spins a round toothed blade to make straight cuts. You rest its flat base plate (the shoe) on the board, line up the blade with your mark, and push the saw forward. A spring-loaded lower guard covers the blade and swings up as you cut.

It is one of the first power tools Filipino carpenters buy: cutting coco lumber and good lumber for framing, ripping plywood for cabinets and ceilings, and trimming boards on site. With the right blade it also cuts aluminum and fiber cement board.

Rough Cut? It's Usually the Blade, Not the Saw

Think of a comb.

A comb with big gaps between its teeth pulls out knots fast. A fine-tooth comb makes hair neat. A saw blade works the same way: few big teeth cut fast but rough; many small teeth cut slower but clean. Put a 24-tooth blade on plywood and the top layer splinters. Put a 60-tooth blade on it and the edge comes out smooth, on the same saw.

Blades are labelled with their diameter and tooth count, for example 7-1/4" x 24T or 7-1/4" x 60T. The "T" is the number of teeth. That number tells you more about the finish you will get than the saw's brand or wattage.

Why 7-1/4 Inch Is the Most Common Circular Saw Size in the Philippines

Circular saws are named by the blade they take. The 7-1/4 inch (185mm) saw is the everyday size here. It cuts through 2-inch lumber in one pass, it is light enough for overhead and site work, and 7-1/4" blades for wood, aluminum and fiber cement are easy to find. Bigger 9-1/4" and 10-1/4" saws cut deeper for heavy timber; compact cordless saws are handy for quick trim cuts.

MOST COMMON

7-1/4" / 185mm

Lumber, coco lumber, plywood, ceiling and cabinet work, general jobsite cutting.

Bosch GKS 140 7-1/4" →
Makita HS7010 7-1/4" →
Total TS1141856 7-1/4" →
HEAVY TIMBER

9-1/4" and up

Deeper cuts in thick beams and posts. Heavier, for experienced users.

Makita N5900B 9-1/4" →
Bosch GKS 235 Turbo 9-1/4" →
NO OUTLET

Cordless

Battery saws for sites without power and quick trim cuts.

Browse cordless circular saws →

Choosing between models? Read our full Circular Saw Buying Guide.

The 4 Circular Saw Blades You Will Use Most

Change the blade on the same 7-1/4" saw and you change what it can cut, and how clean the cut is.

FAST

24T Blade (Few Teeth)

Kahoy · Coco lumber · Framing

Big teeth with deep gullets clear sawdust fast. Best for quick cuts in lumber and coco lumber where a perfect edge does not matter.

Total TAC231413 7-1/4" for Wood →
CLEAN

40T–60T Blade (Many Teeth)

Plywood · Trim · Cabinets

More, smaller teeth take smaller bites, so the veneer on plywood does not tear out. Use it when the cut edge will show.

Bosch 7-1/4" x 40T Expert for Wood →
Bosch 7-1/4" x 60T Multi Material →
NON-FERROUS

Aluminum Blade

Aluminum · Window & door frames

A high tooth count with a tooth shape made for soft metals. Never cut aluminum with a wood blade, and match the blade's diameter to your saw.

Irwin TCT Blade for Aluminum →
Zekoki Blade for Aluminum →
BOARD

Fiber Cement Blade

Fiber cement board · Ceiling & wall board

Very few, very hard tips (often PCD) that survive abrasive cement board far longer than a wood blade. Cement dust is harmful: wear a dust mask and cut outdoors.

Makita A-86088 7-1/4" x 28T →
Makita D-72110 PCD 7-1/4" x 4T →
Tip: Browse every size and tooth count in our Circular Saw Blade collection. Check that the blade's diameter and arbor (centre hole) match your saw before you buy.

Circular Saw Safety Checklist: Bago Ka Mag-Start

Most circular saw injuries come from kickback, when the blade pinches and the saw jumps back toward you. These habits prevent most of them.

  • Make sure the lower guard works, and never tie it back. It must swing freely and snap closed when you lift the saw.
  • Wear goggles and ear protection. Add a dust mask for plywood, MDF and fiber cement. Shop safety goggles and ear protection.
  • Set the depth: only about one tooth below the board. A shallow blade cuts cleaner and leaves less blade exposed if something goes wrong.
  • Support the board and stand to the side. Support both sides so the cut does not close and pinch the blade, and keep your body out of the blade's line, never directly behind the saw.
  • Unplug before changing the blade. Or remove the battery on a cordless saw. Never rely on the switch alone.
Before every cut: check that the blade's maximum RPM is equal to or higher than the saw's speed, that the arrow on the blade matches the saw's rotation, and let the blade reach full speed before it touches the wood. Wait for it to stop before lifting the saw.

Which Blade Do I Need? Choose by Material

When buying, don't just look at the saw. Ask yourself first: "Ano ba ang puputulin ko, at gaano kalinis?" The material and the finish you need tell you which blade to buy.

What are you cutting? Use this blade Shop
Kahoy / coco lumber (fast) 24T wood blade Total TAC231413 7-1/4" · Tatara for Wood
Plywood, trim, cabinets (clean) 40T–60T blade Bosch 7-1/4" x 40T · Bosch 7-1/4" x 60T
Aluminum Aluminum (non-ferrous) blade Irwin TCT for Aluminum · Tatara for Aluminum
Fiber cement board Fiber cement / PCD blade Makita A-86088 · Makita D-72110 PCD
Steel A metal-cutting circular saw with its own blade Circular saws for metal

Frequently Asked Questions

Why does my circular saw splinter plywood?
Usually the blade has too few teeth, or it is dull. Switch to a 40T–60T blade, set the depth to about one tooth below the board, and cut with the good face of the plywood down (the blade's teeth exit on the top).
What size circular saw should a beginner buy?
A 7-1/4 inch (185mm) saw. It is the most common size in the Philippines, cuts 2-inch lumber in one pass, and blades are easy to find.
What does 24T or 60T mean on a saw blade?
The number of teeth. Fewer teeth (around 24T) cut faster and rougher; more teeth (40T–60T and up) cut slower and cleaner.
Can I cut aluminum or fiber cement board with a wood blade?
No. Use a blade made for aluminum, and a fiber cement or PCD blade for cement board. A wood blade dulls fast in cement board and can grab in aluminum.
What causes kickback?
The blade gets pinched in the cut, usually because the board sags and closes on it, or because the saw is twisted mid-cut. Support both sides of the board, keep the saw straight, and stand to the side.
Corded or cordless circular saw?
Corded saws are best for long, continuous cutting. Cordless saws are great where outlets are far or for quick cuts on site.
KHM MEGATOOLS · YOUR NO.1 TOOLSHOP PORTAL

Find the Right Saw and Blade for Your Job

May tanong ka pa? Message us and our team will help you match the right circular saw and blade to your work.

SHOP CIRCULAR SAWS SHOP SAW BLADES SHOP SAFETY GEAR

RELATED ARTICLES

Leave a comment

Your email address will not be published. Required fields are marked *

Please note, comments must be approved before they are published