Stick Welding (SMAW) 101: Setup, Amps & Tips | KHM Megatools

Stick Welding SMAW 101 guide by KHM Megatools Tool Expert Beth
Stick Welding (SMAW) 101: How It Works and How to Use It Right (Philippines 2026)
November 21, 2026
Stick Welding SMAW 101 guide by KHM Megatools Tool Expert Beth
KHM MEGATOOLS · TOOL EXPERT EXPLAINS · WELDING SERIES

Stick Welding (SMAW) 101: How It Works and How to Use It Right

"Isang makina, isang rod... pero ito ang bumubuo ng mga building, barko, at pipeline sa buong mundo." Stick welding is the most common welding process in the world. This guide explains what SMAW is, the basic setup, why welders love it, where it's used, how to strike and run a bead, the right amps for your rod, slag cleaning, and safety.

SHOP ARC / SMAW WELDING HOW TO WELD ↓
Quick Navigation Watch Video What Is SMAW Setup Why It's Popular How to Weld Amps Guide Pro Tip Machines Safety FAQ

Watch: Beth Explains Stick Welding

Prefer watching? Our Tool Expert Beth explains everything in this guide in about two and a half minutes, in Taglish, with captions on screen.

Watch and follow us on your favorite app:

YOUTUBE FACEBOOK INSTAGRAM TIKTOK

What Is SMAW?

SMAW = Shielded Metal Arc Welding, also called ARC welding or stick welding. The rod (electrode) is a metal core coated with flux.

The arc melts the rod and the steel into one.The burning flux turns into a gas that shields the molten weld from the air, then leaves a layer of slag on top that protects the bead while it cools.

The Basic Setup

1 · MACHINE

Welding machine

An inverter like the Hitronic ARC 160 is light and runs on a 220V home outlet.

2 · ELECTRODE HOLDER

The "stinger"

Holds the rod and carries the welding current to it.

3 · GROUND CLAMP

Closes the circuit

Clamp it on clean, bare metal so the arc stays steady. Rust or paint under the clamp makes the arc jumpy.

Why It's the Most Used Welding Process

  • No gas tank: the flux makes its own shielding gas.
  • Portable: easy to bring to the site.
  • Works outdoors and in wind.
  • Tolerates some rust on the steel.
  • All positions: flat, horizontal, vertical and overhead.

Where it's used: structural steel, gates and grills, pipes and tanks, and repairs on heavy equipment and farm tools.

How to Weld: 3 Basics

STEP 1

Strike the arc

Scratch the rod on the steel like lighting a match, then lift slightly.

STEP 2

Keep the arc short

About as long as the rod is thick. Too long = spatter and a weak weld. Too short = the rod sticks.

STEP 3

Drag at a slight angle

Pull the rod, tilted about 10–15° toward the direction of travel, at a steady speed.

Amps Guide (Rule of Thumb)

2.6MM ROD

≈ 60–90 A

3.2MM ROD

≈ 90–130 A

Rod keeps sticking? Amps too low. Lots of spatter? Amps too high. Always check the recommended range on the rod box.

After every pass: chip off the slag with a chipping hammer and wire-brush before the next pass.

Pro Tip: Listen to the Sound

When your setting is right, stick welding sounds like bacon frying: a steady, continuous crackle.

Hitronic Stick Welders

HOME & LIGHT SHOP

Hitronic ARC 160

Inverter, lightweight, digital amp meter, runs on 220V at home. ₱6,800.

VIEW ARC 160
SAFER · WITH VRD

Hitronic ARC 200T / 200CT

VRD (Voltage Reduction Device) drops the idle voltage when you're not welding, for added safety. ₱8,500.

VIEW ARC 200

Prices as of November 2026; check the product page for current price and stock.

Safety Muna

Never look at the arc without eye protection. Arc light can burn your eyes ("arc eye") in seconds.

Next Episode

6013 or 7018: which rod is right for your job?Next episode, Beth explains the difference. Follow us so you don't miss it!

Frequently Asked Questions

Is stick welding good for beginners?
Yes. The setup is simple and needs no gas tank. Practice striking the arc and keeping a short, steady arc on scrap steel first.
Can I stick weld at home on 220V?
Yes. Inverter machines like the Hitronic ARC 160 run on a standard 220V outlet. Use a proper outlet and wire size for the machine's rating.
Why does my rod keep sticking?
Usually the amps are too low or the arc is too short. Raise the amps a little and keep the arc about as long as the rod is thick.
What is VRD on a welding machine?
A Voltage Reduction Device lowers the open-circuit voltage when you're not welding, reducing the risk of electric shock.
Do I have to remove the slag?
Yes. Chip it off and wire-brush after every pass, or it gets trapped in the next pass (slag inclusion) and weakens the weld.
KHM MEGATOOLS · YOUR NO.1 TOOLSHOP PORTAL

Stick Welders, Helmets and Welding Gear

Lahat ng ito, available sa KHM Megatools. May tanong ka pa? I-message mo lang kami, tutulungan ka naming pumili ng tamang makina.

SHOP ARC / SMAW WELDING HITRONIC WELDING MACHINES

RELATED ARTICLES

Leave a comment

Your email address will not be published. Required fields are marked *

Please note, comments must be approved before they are published

Sidebar
Blog categories
Shipping & Delivery

NATIONWIDE DELIVERY

Shipped through trusted third-party couriers

SAME DAY DELIVERY

See how our same-day delivery works

CUSTOMER SUPPORT

Mon–Sat, 8:30AM–5:30PM

RETURNS & EXCHANGES

Read our return, refund & exchange policy

Follow us