Magnetic Drill Press: How to Use It & Where It's Used | KHM Megatools

Magnetic Drill Press guide by KHM Megatools Tool Expert Kiel
Magnetic Drill Press: How to Use It and Where It's Used (Philippines 2026)
November 21, 2026
Magnetic Drill Press guide by KHM Megatools Tool Expert Kiel
KHM MEGATOOLS · TOOL EXPERT EXPLAINS · MAG DRILL SERIES

Magnetic Drill Press: How to Use It and Where It's Used

"Paano bubutasan ang makapal na bakal na beam, nakatayo na sa itaas ng building?" You can't carry the beam to a drill press, so you bring the drill press to the beam. This guide explains how a magnetic drill works, where it's used, the annular cutter, which size to pick, step-by-step usage, speed, a pro tip for thin steel, and safety.

SHOP MAGNETIC DRILLS HOW TO USE ↓
Quick Navigation Watch Video How It Works Where It's Used Annular Cutter Pick a Size How to Use Speed Pro Tip Safety FAQ

Watch: Kiel Explains the Magnetic Drill Press

Prefer watching? Our Tool Expert Kiel explains everything in this guide in about two minutes, in Taglish, with captions on screen.

Watch and follow us on your favorite app:

YOUTUBE FACEBOOK INSTAGRAM TIKTOK

How a Mag Drill Works

An electromagnet in the base.Switch the magnet on and the drill grips the steel tightly, even on a vertical or sideways surface. It's like carrying a drill press anywhere on the job site.

Where It's Used

  • Steel beams and columns of buildings
  • Bridges
  • Shipyards and railways
  • Base plates
  • Fabrication shops

Anywhere steel needs an accurate, clean hole.

The Secret: the Annular Cutter

A twist drill eats the whole hole. An annular cutter only cuts the ring around the edge, so it's:

FASTER

Less metal to cut

EASIER ON THE MOTOR

Less load

THE SLUG

A solid steel piece pops out

The core comes out in one piece, called the slug.

Cutters in stock: Benzwerkz TCT, Benzwerkz HSS, Tatara and DB-1.

Pick a Size by Hole Diameter

UP TO 35 MM · SMALLER JOBS

MaxSell MMD-35

Also: AGP SMD502 2-speed.

VIEW MMD-35
50 MM · MOST STEEL WORK

Bosch GBM 50-2

Also: Dewalt DWE1622K, MaxSell MMD-50, Alfra RB 50X.

VIEW GBM 50-2
UP TO 120 MM · HEAVY DUTY

AGP MD120/4

4-speed. Also: AGP MD750/4, MaxSell MMD-120, Alfra RB 80X.

VIEW MD120/4

Check each product page for current price and stock.

How to Use It, Step by Step

STEP 1

Clean the steel

No rust, thick paint or metal chips, so the magnet sits flat and grips fully.

STEP 2

Mark the hole

Use a center punch, then line the pilot pin up with the mark.

STEP 3

Magnet ON + safety chain

Turn on the magnet, then attach the safety chain.

STEP 4

Cutting oil, then feed slowly

Start the motor and lower the cutter slowly. Let the cutter do the work; don't force it.

Almost through? Ease off the pressure. When you raise the cutter, the pilot pin pushes the slug out. It's hot and sharp, so be careful.

Speed: Bigger Hole, Slower RPM

The bigger the hole, the slower the cutter should turn. That's why there are 2-speed and 4-speed models for bigger cutters.

Pro Tip: Thin Steel

On thin steel the magnet grips weakly. Put a thick steel plate underneath so the magnet holds tight and the drill doesn't move.

Safety Muna

  • Always use the safety chain, especially on vertical or overhead work.
  • Don't weld on the same steel while the drill is attached.
  • When you're done: motor off first, then magnet off, while holding the drill.

Next Episode

TCT or HSS annular cutter: which one fits your job?Next episode, Kiel explains the difference. Follow us so you don't miss it!

Frequently Asked Questions

Can a magnetic drill work on a vertical surface or overhead?
Yes, the electromagnet holds it on vertical and sideways steel. Always attach the safety chain in case the magnet loses grip or power.
Can I use a mag drill on thin steel?
The magnet grips weakly on thin steel. Place a thick steel plate under the work so the magnet holds firmly.
Why use an annular cutter instead of a twist drill?
It only cuts the ring around the hole, so it's faster, puts less load on the motor and leaves a clean hole, with the core coming out as a slug.
Do I need cutting oil?
Yes. Cutting oil cools and lubricates the cutter, for a cleaner hole and longer cutter life.
Which size should I buy?
Go by the biggest hole you'll drill: up to 35 mm for small jobs, 50 mm for most steel work, and up to 120 mm (multi-speed) for heavy duty.
KHM MEGATOOLS · YOUR NO.1 TOOLSHOP PORTAL

Magnetic Drills and Annular Cutters

Lahat ng ito, available sa KHM Megatools. May tanong ka pa? I-message mo lang kami, tutulungan ka naming pumili ng tamang mag drill at cutter.

SHOP MAGNETIC DRILLS & CUTTERS

RELATED ARTICLES

Leave a comment

Your email address will not be published. Required fields are marked *

Please note, comments must be approved before they are published

Sidebar
Blog categories
Shipping & Delivery

NATIONWIDE DELIVERY

Shipped through trusted third-party couriers

SAME DAY DELIVERY

See how our same-day delivery works

CUSTOMER SUPPORT

Mon–Sat, 8:30AM–5:30PM

RETURNS & EXCHANGES

Read our return, refund & exchange policy

Follow us