Pump Keeps Turning On and Off? 5 Causes & Fixes | KHM Megatools PH

Bobby of KHM Megatools explains why a water pump keeps turning on and off: pressure switch, tank air, check valve and tank size
Why Does My Water Pump Keep Turning On and Off? 5 Causes and Fixes (Philippines 2026)
November 21, 2026
Bobby of KHM Megatools explains why a water pump keeps turning on and off: pressure switch, tank air, check valve and tank size
KHM MEGATOOLS · TOOL EXPERT EXPLAINS · WATER PUMP SERIES EP. 2

Why Does My Water Pump Keep Turning On and Off? 5 Causes and Fixes

"On-off nang on-off ang pump mo kahit walang gumagamit ng tubig?" That's called short cycling, and it slowly kills your pump. This guide explains why it's dangerous, the five most common causes with a quick check for each, what to do when the pump runs but no water comes out, and how to stay safe while troubleshooting.

SHOP WATER PUMPS THE 5 CAUSES ↓
Quick Navigation Watch Video What Is Short Cycling 5 Causes No Water? Pro Tip Safety Next Episode FAQ

Watch: Bobby Explains Pump Short Cycling

Prefer watching? Our Tool Expert Bobby explains everything in this guide in about two minutes, in Taglish, with captions on screen. Missed episode 1? Read Residential Water Pump Installation: Pressure Tank or Tankless?

Watch and follow us on your favorite app:

YOUTUBE FACEBOOK INSTAGRAM TIKTOK

What Is Short Cycling and Why Is It Bad?

Short cycling is when the pump starts and stops again and again in a short time, even when nobody is using water. Every start pulls a big surge of power, so frequent starts:

  • Overheat the motor.
  • Wear out the capacitor and the pressure switch contacts.
  • Raise your electric bill.

The 5 Common Causes (and Quick Checks)

CAUSE #1 · LEAKS

A drip somewhere

A dripping faucet, a toilet that keeps running, or a leaking pipe. Test: close every faucet and watch the pressure gauge. If the pressure keeps dropping, there's a leak.

CAUSE #2 · TANK LOST ITS AIR

No air cushion left

Without air, the tank has no reserve, so the pump starts right away. Check the air with a tire gauge while the tank is empty of water. If water comes out when you press the air valve, the bladder is torn. See bladder pressure tanks.

CAUSE #3 · CHECK / FOOT VALVE

Water flows back

A bad check valve or foot valve lets water flow back, the pressure drops, and the pump starts again. Sometimes the pump also loses its prime.

CAUSE #4 · PRESSURE SWITCH

Settings, contacts or a clogged hole

Cut-in and cut-out set too close together, worn contacts, or a clogged small inlet hole under the switch. Replacement: Hoover HPS5-A pressure switch (20–40 psi).

CAUSE #5 · TANK TOO SMALL

Not enough reserve

A pressure tank that's too small for the pump empties fast, so the pump cycles often. Compare a small built-in tank like the Lotus LM100X 24L with a bigger 60–100L tank.

Pump Runs but No Water Comes Out?

Usually there's air in the line. Check for:

  • A leak on the suction side that lets air in.
  • Low water in the storage tank.
  • A foot valve that doesn't close.
Fix: tighten the fittings using teflon tape, then prime the pump again.

Pro Tip: Put a Pressure Gauge Near the Tank

With a pressure gauge near the tank, one look tells you if there's a leak or if the settings are right.

Safety Muna

  • Switch off the breaker.
  • Open a faucet to release the pressure before touching the pump, the switch or the tank.

Next Episode

Ilang HP ba talaga ang kailangan ng bahay mo?In episode 3 Bobby explains how to size a pump for your home. Follow us so you don't miss it!

Frequently Asked Questions

How often should a home pump start?
It should only start when water is being used, and then run for a while. Starting every few seconds or minutes with no water use is short cycling.
How do I check the pressure tank air?
Switch off the pump, open a faucet until the tank is empty of water, then check the air valve with a tire gauge. It should be about 2 psi below the pump's cut-in pressure.
Water comes out of the tank's air valve. What now?
The rubber bladder inside is torn. Replace the bladder or the tank.
Can a bad pressure switch cause short cycling?
Yes: settings too close together, worn contacts, or a clogged inlet hole under the switch can all make the pump cycle.
Can I fix it myself?
Simple checks like leaks, tank air and cleaning the switch inlet are easy. Always switch off the breaker and release the pressure first. Message us if you need help choosing parts.
KHM MEGATOOLS · YOUR NO.1 TOOLSHOP PORTAL

Pressure Switch, Pressure Tank, Check Valve and Gauge

Lahat 'yan available sa KHM Megatools. May tanong ka pa? I-message mo lang kami, tutulungan ka naming hanapin ang dahilan.

SHOP WATER PUMPS PRESSURE TANKS

RELATED ARTICLES

Leave a comment

Your email address will not be published. Required fields are marked *

Please note, comments must be approved before they are published

Sidebar
Blog categories
Shipping & Delivery

NATIONWIDE DELIVERY

Shipped through trusted third-party couriers

SAME DAY DELIVERY

See how our same-day delivery works

CUSTOMER SUPPORT

Mon–Sat, 8:30AM–5:30PM

RETURNS & EXCHANGES

Read our return, refund & exchange policy

Follow us